You don’t want to have the benches or the table top going past the legs or you won’t be able to screw in the legs flush with the tree. Then you can put screws through the legs into your tree of choice. However, if you do, just be sure that in this step and the next step you make the benches and the table top flush with the table legs. I didn’t want to screw it into one of our trees. I made my squirrel picnic table with the plan of putting it wherever I wanted on our patio. If the tops of the legs are straight, then the bottom of the legs will be straight and your table with stand without wobbling. Hint: Make sure the tops of the legs are straight. Center the legs lengthwise along the braces so the same amount of brace is hanging over the legs on both sides. Make sure the top edge of the legs are straight and the tips touch. Lay the brace along the pencil mark across the legs. Measure 1″ up from the bottom of the legs and mark with a pencil. Now we can start putting them all together with nails and wood glue. Required wood pieces include 2 braces, 2 benches, 1 top, and 4 legs. Once you’ve got all the needed wood pieces, they should look similar to this when you lay them all out: To get the angled look of the legs, measure 1.5″ down the leg from opposite sides of the top and bottom, mark a line, and cut the parallel angled edges. If that’s not a requirement for you, don’t worry about this size being exact either. If you’re going to want to attach your table to a tree, the benches need to be the exact same length as the table top. I ended up needing a lot of wood glue because my braces were too porous. I used particle board and would not recommend it–a normal tougher wood would be better for the braces. These pieces are going to attach the benches to the legs of your picnic table. For example, you could cut 3 pieces that are 10″ x 2.5.” For mine, I had a piece of wood that was a little bigger than that and I didn’t even bother cutting it smaller. If you don’t have scrap wood that big, you can combine smaller pieces. Remember, this is the final size that you want, but it doesn’t have to be exact. They’re going to love it for the food! Wood Pieces Needed for Squirrel Picnic Table This is for the squirrels in your yard after all–they won’t care if it is made with old wood or imperfect in some way. For this project, I got out a wood pallet, found an old piece of particle board, and part of a wood panel.ĭon’t be afraid to use what you’ve got handy–you can always cut it to the size you need or combine smaller pieces to make a bigger size.įor example, I could’ve cut everything out of the wood pallet, but I already had a few other pieces that were about the right size. Steps to Make Your Own Squirrel Picnic Table Step 1: Cut your scrap wood into the pieces that you need for the mini table. Supplies Needed for Squirrel Picnic Table I modeled mine off the instructions from this website: How to make a squirrel picnic table – free PDF plans! () and tweaked it for what I had on hand. That being said, I knew I had some scrap wood in my garage, so I wanted to try a DIY project to make the squirrel picnic table. Though if you decide you’d rather just skip the DIY project and buy your squirrel picnic table, this one looked to be the best deal: I was pretty sure I could make one for next to nothing. Prices ranged from $20 to $40 for these mini tables. Aww!īut when I saw the price for a squirrel picnic table, I decided to try to make my own. When I saw one, I thought it was the cutest thing! With the little squirrels sitting on the little benches and nibbling on seeds or corn on the cob. Have you seen these adorable mini picnic tables? I had no idea until my sister introduced me to the concept. Apparently, squirrel picnic tables are popular right now.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |